The two-part setup: protector first, case second
A screen protector and a case do different jobs, and the order you install them matters. The Glass Screen Protector for iPhone 15 is designed to shield your display from bumps and scrapes while keeping touch sensitivity high. The Pelican Voyager Clear MagSafe case adds drop protection and a built-in magnet array for MagSafe charging.
Install the protector on a clean, bare iPhone 15 screen first. Then fit the case. This sequence lets you align the glass without the case edge interfering, and it avoids lifting the protector while you snap the case on.
What the Glass Screen Protector record confirms
- Glass Screen Protector - iPhone 15: Tempered glass construction with ultra-high clarity and bubble-free application. Clarity and a bubble-free fit are the two things you will notice immediately after installation.

Glass Screen Protector - iPhone 15 - Glass Screen Protector - iPhone 15: Fits most phone cases and maintains touch sensitivity. This is the compatibility checkpoint for pairing it with the Voyager Clear case.
How to apply the glass protector on your iPhone 15
The product record confirms an easy, bubble-free application but does not list a step-by-step procedure. The steps below are general best practice for tempered glass protectors, not manufacturer instructions. Check the packaging for any specific guidance before you begin.
- Work on a clean, dust-free surface: Wash your hands and clear a table. Dust is the main cause of bubbles and trapped specks.
- Clean the iPhone 15 screen thoroughly: Use a microfiber cloth to remove fingerprints and smudges. If your protector kit includes a dust sticker or alcohol wipe, use it now.
- Dry-fit the protector before peeling any film: Hold the glass above the screen and check that the cutouts for the speaker and camera align. Do not remove the backing yet.
- Peel the backing and lower the glass slowly: Start from one edge and let the glass settle. Avoid pressing down until the whole sheet is in contact.
- Press out bubbles from the center outward: Use your thumb or a soft card wrapped in cloth. Small edge bubbles often disappear over the first day or two.
- Check touch sensitivity before adding the case: Swipe around the screen and test the keyboard. The record confirms the protector maintains touch sensitivity; if something feels off, reseat the protector before moving on.
What the Pelican Voyager Clear MagSafe record confirms
- Pelican Voyager Clear MagSafe - iPhone 15: Dual-layer impact protection with 18-foot drop protection and a non-slip edge. This is the case's core protection claim, and the non-slip edge helps with grip during everyday use.

Pelican Voyager Clear MagSafe - iPhone 15 - Pelican Voyager Clear MagSafe - iPhone 15: Strong built-in magnets for MagSafe charging. The magnets are intended to align with MagSafe accessories and chargers, so you do not need to remove the case to charge.
Fitting the Voyager Clear case over the protector
The case record does not include installation steps, so treat the following as practical checkpoints rather than manufacturer instructions.
- Seat the phone bottom-first: Slide the iPhone 15 into the case starting at the bottom edge, then press the top corners in. This reduces the chance of catching the screen protector edge.
- Check the protector edge: The Glass Screen Protector record says it fits most phone cases. After fitting the Voyager Clear, run a finger around the edge. If the case lifts a corner of the glass, reseat the case or the protector.
- Confirm button and port access: Press each button and plug in a cable to make sure the case does not block normal use.
- Test MagSafe alignment: Attach a MagSafe charger or accessory. The built-in magnets should hold it in place. The record does not specify charging speed, so judge alignment and hold, not wattage.
What the records do not settle
Neither product record lists a full installation procedure, care instructions, or exact compatibility beyond the iPhone 15 model. The screen protector's case compatibility is described as fitting most phone cases, not as a guarantee for every case. If you use a different case, check the fit before relying on the protector's edge coverage.
The Voyager Clear record confirms MagSafe charging support but does not state charging performance or accessory compatibility beyond MagSafe. If you use a third-party magnetic accessory, test the hold before trusting it.
For care, the records do not include cleaning agents or methods. A dry microfiber cloth is a safe general choice for both glass and case surfaces, but follow any care information included in the packaging.


